Viscosity Tubes

Reverse-flow type, for measurement of kinematic viscosity of dark Newtonian liquids according to ASTM D 445 and ISO 3104. Permit measurements of liquids whose meniscus cannot be seen at the timing marks when using a Cannon-Fenske Routine type viscometer. Factory calibration certificate is supplied. Requires minimum sample volume of 12mL. Used to measure kinematic viscosity of...

Cannon^®-Manning Vacuum Viscosity Tubes are for measurement of viscosity of highly viscous materials such as asphalt cement at 60°C (140°F) according to ASTM D 2171. Applicable to materials with viscosity range of 0.036 to 80 000 poise. Vacuum of 300 mm Hg is applied to small arm with timing bulbs; two bulbs are incorporated to extend viscosity range of viscometer....

Suspended level (Cannon Ubbelohde) viscometers are used for measurement of kinematic viscosity of transparent Newtonian liquids according to ASTM D 445 and ISO 3104. Also used for evaluating jet and hydraulic lubricants. Especially suited for use at temperatures above 93°C (200°F) or below -18°C (0°F). Require no kinetic energy corrections over 0.5 to 100 000 centistokes range...

For measurement of kinematic viscosity of transparent Newtonian liquids by suspended level principle as described in ASTM D445 and D446, and ISO 3104 and 3105. Provided with certificate of calibration. Minimum sample volume 11mL. Requires liquid bath depth of 241 mm (9.5"). For a more rugged design, see Cannon-Ubbelohde Viscosity tubes (P4552).

For measuring kinematic viscosity of transparent Newtonian liquids, particularly petroleum products or lubricants, according to ASTM D 445 and ISO 3104. These tubes are factory calibrated. Specifications conform to ASTM D 446 and ISO 3105. Approximately 7 mL of sample is needed. If you are measuring liquids whose meniscus cannot be seen at the timing marks, use the Cannon-...

For measuring kinematic viscosity of transparent Newtonian liquids, particularly petroleum products or lubricants, according to ASTM D 445 and ISO 3104. These tubes are factory calibrated. Specifications conform to ASTM D 446 and ISO 3105. Approximately 7 mL of sample is needed. If you are measuring liquids whose meniscus cannot be seen at the timing marks, use the Cannon-...

For measuring kinematic viscosity of transparent Newtonian liquids, particularly petroleum products or lubricants, according to ASTM D 445 and ISO 3104. These tubes are factory calibrated. Specifications conform to ASTM D 446 and ISO 3105. Approximately 7 mL of sample is needed. If you are measuring liquids whose meniscus cannot be seen at the timing marks, use the Cannon-...

For measuring kinematic viscosity of transparent Newtonian liquids, particularly petroleum products or lubricants, according to ASTM D 445 and ISO 3104. These tubes are factory calibrated. Specifications conform to ASTM D 446 and ISO 3105. Approximately 7 mL of sample is needed. If you are measuring liquids whose meniscus cannot be seen at the timing marks, use the Cannon-...

For measuring kinematic viscosity of transparent Newtonian liquids, particularly petroleum products or lubricants, according to ASTM D 445 and ISO 3104. These tubes are factory calibrated. Specifications conform to ASTM D 446 and ISO 3105. Approximately 7 mL of sample is needed. If you are measuring liquids whose meniscus cannot be seen at the timing marks, use the Cannon-...

For measuring kinematic viscosity of transparent Newtonian liquids, particularly petroleum products or lubricants, according to ASTM D 445 and ISO 3104. These tubes are factory calibrated. Specifications conform to ASTM D 446 and ISO 3105. Approximately 7 mL of sample is needed. If you are measuring liquids whose meniscus cannot be seen at the timing marks, use the Cannon-...